Brownells Roll Pin Holders #2 5/64"(2.0mm) Dia 4 1/2"(11.4cm) O/A Length Specification Information
Gunsmith Punches by Brownells
|
Specification information: Holds roll pins perfectly aligned for starting correctly. Especially good on the tiny, tough-to-grab ones, or those in tight places. 1/16" is notched to clear m16/ar-15 rear sight. 3.5mm excellent for holding the pin that retains the breech block on sig handguns. Finish driving with roll pin punch. O/a in chart means "overall". Available individually or as a set of 5. Mfg: brownells specs: steel, knurled handle. Set of 5. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-685-078.
 Indicative Price: USD 14.99
(for Actual Current Price, possibly lower,
please click below)
More Info & Supplier : click here
For more high specification gun & shooting products : click here
|
Try Search on this site - find exactly what you need! Click below:
|
|
|
|
 |
|
|
|
Brownells Roll Pin Starter Punches #1 Punch Specification Information
USD 5.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Mfg: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2mm); #3, 3/32" (2.4mm), #4, 1/8" (3.2mm); #5, 5/32" (4mm); #6, 3/16" (4.8mm); 7/32" (5.5mm); #7, 7/32" (5.5mm). Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 25030939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Premium Roll Pin Holders Set Specification Information
USD 31.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: Brownells roll spring (pin) holders are accurately drilled to hold tiny roll springs so perfect alignment is obtained. The 1/16" roll spring (pin) holder is notched to clear m16/ar-15 rear sights. The 3.5mm is excellent for holding the pin that retains the breech block on sig handguns. This fine set has sizes 1/16" (notched), 5/64", 3/32", 1/8", 3.5mm and each made from 5/16" hex high carbon 5160 steel that is bainite heat treated for strength. Single groove in grip section and laser marked for quick identification. 100% made in the usa. Mfg: brownells. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: BRSHS.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Cup Tip Punches Set A Specification Information
USD 46.69
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: Eight concave "cupped" tip punches to precisely fit the round head pins found on smith & wesson handguns. Won't flatten the pin top and ruin the gun's looks. Made to the same specs as those used by the factory. Use 3mm punch on sig handguns. Complete set (set d listed below) includes a delrin bench block that holds and organizes all eight punches. Bench block also available separately 080-000-644. Mfg: brownells specs: punches, steel. 5/16" (7.9mm) wide hex handle. .057" (1.44mm)/long; .066" (1.7mm)/long; .072" (1.8mm/long; .040" (1mm)/short; .050" (1.3mm)/short; .050" (1.3mm)/long; 3mm (.118")/long; 3mm (.118")/short. Bench bl. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-620-103.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Punches #2 Roll Pin Punch Specification Information
USD 7.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: With these pins becoming so common in guns, having the right punches to remove them is absolutely necessary. These punches are the only way to remove and re-use roll or spring pins without causing glaring damage to the pins. Solid steel punches, with long, parallel-ground points and knurled section for better gripping. Mfg: brownells specs: kit includes one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2.0mm); #3, 3/32" (2.4mm); #4, 1/8" (3.2mm); #5, 5/32" (4.0mm); #6, 3/16" (4.8mm); #7, 7/32" (5.5mm). Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 25001939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Starter Punch Set Replaceable Starter Punch .039 Dia. Specification Information
USD 9.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: We are constantly encouraging you to always use starting punches to break tight pins loose, then use a "drift" or pin-punch to drive the pin the rest of the way out. This saves bending pin punches, but much more importantly, it prevents fine guns from getting pin punch mars should the pin punch bend and slip, or, break, and scratch. To bring you the best possible starter punches, we have had special, short replaceable pins made up to fit our famous gunsmith's replacement punch set handles. Their regular use will definitely improve your production . . . And your professionalism! mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins 1" (2.5cm) long. Set includes 3 punches and three pins. Replacement pin sizes: .039" (.99mm) for 3⁄64" (1.2mm) diameter pins. .060" (1.5mm) for 1⁄16" (1.6mm) diameter pins; .091" (2.3mm) for 3⁄32" (2.4mm) diameter pins. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-513-039.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Nylon/Brass Drift Punch Nylon Punch Tip Specification Information
USD 4.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: Great combination punch for gunsmith, machinist and toolmaker. Hi-impact steel handle with knurled grip for easy holding and accurate control. Built to withstand maximum impact with a minimum of distortion. Interchangeable and replaceable tips are available in: 5/16" nylon with steel reinforcing pin to prevent bending or breakage while giving completely mar-free punching action; brass in various diameters for a harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Aluminum in two diamters for harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Remington shotgun punch tip which is .165" di mfg: brownells specs: handle is 3" (7.6cm) long x 3.8" (9.5mm) diamter. Tips are 1βό" (3.2cm) long. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-475-001.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Cup Tip Punches Model 4 .040" (1.0mm) Diameter/Short Length Specification Information
USD 17.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: Eight concave "cupped" tip punches to precisely fit the round head pins found on smith & wesson handguns. Won't flatten the pin top and ruin the gun's looks. Made to the same specs as those used by the factory. Use 3mm punch on sig handguns. Complete set (set d listed below) includes a delrin bench block that holds and organizes all eight punches. Bench block also available separately 080-000-644. Mfg: brownells specs: punches, steel. 5/16" (7.9mm) wide hex handle. .057" (1.44mm)/long; .066" (1.7mm)/long; .072" (1.8mm/long; .040" (1mm)/short; .050" (1.3mm)/short; .050" (1.3mm)/long; 3mm (.118")/long; 3mm (.118")/short. Bench bl. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-620-004.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Hole Center Punches #8 Hole Center Punch Specification Information
USD 8.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: 3 special center punches with outside diameters (o.D.) that match the clearance drill size of the most popular sight, rib and scope base mounting screws. Ground, parallel-sided punches reach through even the thickest handgun rib. Ends guess-work and hole center-to-center spacing problems. To use: level gun in vise or scope mounting jig, position and level sight, rib or base, and clamp in place. Place correct size punch in hole and lightly tap with a 4-oz. Hammer. Remove base; drill and tap first hole; re-install base and check positioning. If everything is "square", re-clamp and finish other holes. Mfg: brownells specs: 2-βύ" (7.0cm) long. ß?" (6.3cm) dia. Knurled handle. Hardened, tool steel. Set contains one of each size. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-732-008.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Cup Tip Punches Model 7 3mm (.118") Diameter/Long Length Specification Information
USD 12.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: Eight concave "cupped" tip punches to precisely fit the round head pins found on smith & wesson handguns. Won't flatten the pin top and ruin the gun's looks. Made to the same specs as those used by the factory. Use 3mm punch on sig handguns. Complete set (set d listed below) includes a delrin bench block that holds and organizes all eight punches. Bench block also available separately 080-000-644. Mfg: brownells specs: punches, steel. 5/16" (7.9mm) wide hex handle. .057" (1.44mm)/long; .066" (1.7mm)/long; .072" (1.8mm/long; .040" (1mm)/short; .050" (1.3mm)/short; .050" (1.3mm)/long; 3mm (.118")/long; 3mm (.118")/short. Bench bl. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: SML004257.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Starter Punch Set Replaceable Starter Punch .091 Dia. Specification Information
USD 9.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: We are constantly encouraging you to always use starting punches to break tight pins loose, then use a "drift" or pin-punch to drive the pin the rest of the way out. This saves bending pin punches, but much more importantly, it prevents fine guns from getting pin punch mars should the pin punch bend and slip, or, break, and scratch. To bring you the best possible starter punches, we have had special, short replaceable pins made up to fit our famous gunsmith's replacement punch set handles. Their regular use will definitely improve your production . . . And your professionalism! mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins 1" (2.5cm) long. Set includes 3 punches and three pins. Replacement pin sizes: .039" (.99mm) for 3⁄64" (1.2mm) diameter pins. .060" (1.5mm) for 1⁄16" (1.6mm) diameter pins; .091" (2.3mm) for 3⁄32" (2.4mm) diameter pins. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-513-091.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Punches #7 Roll Pin Punch Specification Information
USD 8.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: With these pins becoming so common in guns, having the right punches to remove them is absolutely necessary. These punches are the only way to remove and re-use roll or spring pins without causing glaring damage to the pins. Solid steel punches, with long, parallel-ground points and knurled section for better gripping. Mfg: brownells specs: kit includes one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2.0mm); #3, 3/32" (2.4mm); #4, 1/8" (3.2mm); #5, 5/32" (4.0mm); #6, 3/16" (4.8mm); #7, 7/32" (5.5mm). Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 25006939.
More Details : click here
SEARCH this site : click here
|
|
|
|
|
|
Try Search on this site - find exactly what you need! Click below:
|
|
Item on this page: Brownells Roll Pin Holders #2 5/64"(2.0mm) Dia 4 1/2"(11.4cm) O/A Length Specification Information
|
 Copyright © USAGunCache.com : 1997 - 2026 : All rights reserved. 140-UNI
|
|
