Brownells Hole Center Punches #10 Hole Center Punch Specification Information
Gunsmith Punches by Brownells
|
Specification information: 3 special center punches with outside diameters (o.D.) that match the clearance drill size of the most popular sight, rib and scope base mounting screws. Ground, parallel-sided punches reach through even the thickest handgun rib. Ends guess-work and hole center-to-center spacing problems. To use: level gun in vise or scope mounting jig, position and level sight, rib or base, and clamp in place. Place correct size punch in hole and lightly tap with a 4-oz. Hammer. Remove base; drill and tap first hole; re-install base and check positioning. If everything is "square", re-clamp and finish other holes. Mfg: brownells specs: 2-βύ" (7.0cm) long. ß?" (6.3cm) dia. Knurled handle. Hardened, tool steel. Set contains one of each size. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-732-010.
 Indicative Price: USD 3.99
(for Actual Current Price, possibly lower,
please click below)
More Info & Supplier : click here
For more high specification gun & shooting products : click here
|
Try Search on this site - find exactly what you need! Click below:
|
|
|
|
 |
|
|
|
Brownells Roll Pin Starter Punches #7 Punch Specification Information
USD 3.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Mfg: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2mm); #3, 3/32" (2.4mm), #4, 1/8" (3.2mm); #5, 5/32" (4mm); #6, 3/16" (4.8mm); 7/32" (5.5mm); #7, 7/32" (5.5mm). Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 25036939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Cup Tip Punches Model 2 .066" (1.7mm) Diameter/Long Length Specification Information
USD 17.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: Eight concave "cupped" tip punches to precisely fit the round head pins found on smith & wesson handguns. Won't flatten the pin top and ruin the gun's looks. Made to the same specs as those used by the factory. Use 3mm punch on sig handguns. Complete set (set d listed below) includes a delrin bench block that holds and organizes all eight punches. Bench block also available separately 080-000-644. Mfg: brownells specs: punches, steel. 5/16" (7.9mm) wide hex handle. .057" (1.44mm)/long; .066" (1.7mm)/long; .072" (1.8mm/long; .040" (1mm)/short; .050" (1.3mm)/short; .050" (1.3mm)/long; 3mm (.118")/long; 3mm (.118")/short. Bench bl. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-620-002.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Brass Punch Set Specification Information
USD 119.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: Precision machined, non-marring brass punches drift sights and drive pins without risk of damage to the sight, pin, or firearm. We combined 20 of our most popular non-marring brass punches, added a compact bench block and came up with a great addition for the work bench. Features (4) starter punches, (8) roll pin punches, and (8) standard punches for a variety of different jobs. Delrin bench block holds and organizes all 20 punches for easy access, plus is resistant to most solvents. Starter punches are used to start the removal of steel or aluminum pins. Short, tapered shaft is extra stiff to prevent bending and twisting. Roll pin punches feature a special tip that centers inside the h mfg: brownells specs: brass. Starter punches, contains (1) of each diameter: 1⁄16" (1.6mm), 3⁄32" (2.4mm), 1⁄8" (3.2mm), 5⁄32" (4mm). Roll pin punches, contains (1) of each diameter: 1⁄16", 3⁄32", 1⁄8", 5⁄32", 3⁄16". Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-000-649.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Punches #7 Roll Pin Punch Specification Information
USD 8.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: With these pins becoming so common in guns, having the right punches to remove them is absolutely necessary. These punches are the only way to remove and re-use roll or spring pins without causing glaring damage to the pins. Solid steel punches, with long, parallel-ground points and knurled section for better gripping. Mfg: brownells specs: kit includes one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2.0mm); #3, 3/32" (2.4mm); #4, 1/8" (3.2mm); #5, 5/32" (4.0mm); #6, 3/16" (4.8mm); #7, 7/32" (5.5mm). Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 25006939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Gunsmith Replaceable Pin Punch Set Replacement Pin Punch 2" Long .039 Dia. Specification Information
USD 10.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: Finally! what we think is the answer to the pin punch headache that has plagued us, and every other gunsmith who has ever knocked out a gun pin, had the punch break or bend, and been out of business until a new one could be made or ordered. Now, just replace the tip!handles, with removable knurled-chuck to hold punch, are made of powerful, fatigueproof c.R.S. Steel, tensile strength of over 140,000 psi (min.). Replaceable punch, the secret of the tool. These are special, tool steel, bevel-headed punches designed for the tool, die and mold manufacturers as perforators, punches, ejectors and core pins. Oil hardened to rc 58-60. Heads are annealed to rc 42-45. They come in two lengths a mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins are 2" (5.1cm) or 2β½" (6.3cm) long. Replacement pin punch sets include the following pin sizes: 0.039", 0.060", and 0.091" in either 2" or 2 β½" lengths. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-507-239.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Nylon/Brass Drift Punch 1/4" Brass Punch Tip Specification Information
USD 5.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: Great combination punch for gunsmith, machinist and toolmaker. Hi-impact steel handle with knurled grip for easy holding and accurate control. Built to withstand maximum impact with a minimum of distortion. Interchangeable and replaceable tips are available in: 5/16" nylon with steel reinforcing pin to prevent bending or breakage while giving completely mar-free punching action; brass in various diameters for a harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Aluminum in two diamters for harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Remington shotgun punch tip which is .165" di mfg: brownells specs: handle is 3" (7.6cm) long x 3.8" (9.5mm) diamter. Tips are 1βό" (3.2cm) long. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-475-003.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Dovetail Sight Punch Dovetail Punch Kit Specification Information
USD 21.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: These punches are specifically designed for the installation, removal, and adjustment of front and rear handgun sights. Made of brass so they will not mar the sight or the gun if you slip. Unique triangular punch faces and heavy-duty bodies make them indispensable working tools for the gunsmith. Can be re-ground to square up the flat after multiple uses. Front sight punch has a base width of approximately .280"; rear sight punch has a base width of approximately 0.480". They are sold separately or can be purchased together in a handy kit. The small dovetail sight punch (sold separately) has a .230" base width, making it ideal for front and rear sights on compact handguns. Mfg: brownells. Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-001-164.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Punches #6 Roll Pin Punch Specification Information
USD 2.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: With these pins becoming so common in guns, having the right punches to remove them is absolutely necessary. These punches are the only way to remove and re-use roll or spring pins without causing glaring damage to the pins. Solid steel punches, with long, parallel-ground points and knurled section for better gripping. Mfg: brownells specs: kit includes one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2.0mm); #3, 3/32" (2.4mm); #4, 1/8" (3.2mm); #5, 5/32" (4.0mm); #6, 3/16" (4.8mm); #7, 7/32" (5.5mm). Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 25005939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Starter Punches #2 Punch Specification Information
USD 7.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Mfg: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2mm); #3, 3/32" (2.4mm), #4, 1/8" (3.2mm); #5, 5/32" (4mm); #6, 3/16" (4.8mm); 7/32" (5.5mm); #7, 7/32" (5.5mm). Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 25031939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches .246" Diameter Brass Specification Information
USD 8.99
(Indicative price - actual current price possibly lower)
Brownells Gunsmith Punches Specification Info
Specification information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). Reliable & durable gunsmith punches by Brownells. Manufacturer MPN: 080-000-027.
More Details : click here
SEARCH this site : click here
|
|
|
|
|
|
Try Search on this site - find exactly what you need! Click below:
|
|
Item on this page: Brownells Hole Center Punches #10 Hole Center Punch Specification Information
|
 Copyright © USAGunCache.com : 1997 - 2026 : All rights reserved. 140-UNI
|
|
